Articles citing this article

The Citing articles tool gives a list of articles citing the current article.
The citing articles come from EDP Sciences database, as well as other publishers participating in CrossRef Cited-by Linking Program. You can set up your personal account to receive an email alert each time this article is cited by a new article (see the menu on the right-hand side of the abstract page).

Cited article:

This article has been cited by the following article(s):

An image processing algorithm for detection and analysis of slicing checks

Victor Grubîi and Jimmy Johansson
European Journal of Wood and Wood Products 79 (4) 999 (2021)
DOI: 10.1007/s00107-021-01672-8
See this article

Root cause and vibration analysis to increase veneer manufacturing process efficiency: a case study on an industrial peeling lathe

Víctor Tuninetti, Ricardo Alzugaray, Jorge González, Marian Valenzuela, Andrés Jaramillo and Eduardo Diez
European Journal of Wood and Wood Products 79 (4) 951 (2021)
DOI: 10.1007/s00107-021-01705-2
See this article

Recovery rate and quality of rotary peeled veneer from 30-year-old Pinus taeda L. logs

Mário Dobner JR., Leif Nutto and Antonio R. Higa
Annals of Forest Science 70 (4) 429 (2013)
DOI: 10.1007/s13595-013-0274-z
See this article

Simultaneous measurement of lathe check depth and the grain angle of birch (Betula pendula Roth) veneers using laser trans-illumination imaging

Toni Antikainen, Joona Eskelinen, Anti Rohumaa, Teemu Vainio and Mark Hughes
Wood Science and Technology 49 (3) 591 (2015)
DOI: 10.1007/s00226-015-0718-8
See this article

Cutting forces in wood machining – Basics and applications in industrial processes. A review COST Action E35 2004–2008: Wood machining – micromechanics and fracture

Rémy Marchal, Frédéric Mothe, Louis-Etienne Denaud, Bernard Thibaut and Laurent Bleron
Holzforschung 63 (2) 157 (2009)
DOI: 10.1515/HF.2009.014
See this article

Wood peeling process monitoring: a comparison of signal processing methods to estimate veneer average lathe check frequency

Louis Etienne Denaud, Laurent Bléron, Florent Eyma and Rémy Marchal
European Journal of Wood and Wood Products 70 (1-3) 253 (2012)
DOI: 10.1007/s00107-011-0549-8
See this article

Properties of wood surfaces – characterisation and measurement. A review COST Action E35 2004–2008: Wood machining – micromechanics and fracture

Gerhard Sinn, Jakub Sandak and Tahiana Ramananantoandro
Holzforschung 63 (2) 196 (2009)
DOI: 10.1515/HF.2009.016
See this article

Numerical study of the influence of veneer lathe checks on the elastic mechanical properties of laminated veneer lumber (LVL) made of beech

Guillaume Pot, Louis-Etienne Denaud and Robert Collet
Holzforschung 69 (3) 337 (2015)
DOI: 10.1515/hf-2014-0011
See this article

Peeling of small diameter rubber log using spindleless lathe technology: evaluation of veneer properties from outer to inner radial section of log at different veneer thicknesses

Pui San Khoo, Paik San H’ng, Kit Ling Chin, et al.
European Journal of Wood and Wood Products 76 (4) 1335 (2018)
DOI: 10.1007/s00107-018-1300-5
See this article

Lathe check development and properties: effect of log soaking temperature, compression rate, cutting radius and cutting speed during peeling process of European beech (Fagus sylvatica L.) veneer

Anti Rohumaa, Joffrey Viguier, Stéphane Girardon, Michael Krebs and Louis Denaud
European Journal of Wood and Wood Products 76 (6) 1653 (2018)
DOI: 10.1007/s00107-018-1341-9
See this article

Physical properties and bonding quality of laminated veneer lumber produced with veneers peeled from small-diameter rubberwood logs

P. S. Khoo, K. L. Chin, P. S. H'ng, et al.
Royal Society Open Science 6 (12) 191763 (2019)
DOI: 10.1098/rsos.191763
See this article

Wood machining with a focus on French research in the last 50 years

Bernard Thibaut, Louis Denaud, Robert Collet, et al.
Annals of Forest Science 73 (1) 163 (2016)
DOI: 10.1007/s13595-015-0460-2
See this article

A Method of Lathe Checks Measurement; SMOF device and its software

Bartosz Pałubicki, Rémy Marchal, Jean-Claude Butaud, et al.
European Journal of Wood and Wood Products 68 (2) 151 (2010)
DOI: 10.1007/s00107-009-0360-y
See this article

The influence of veneer thickness and knot proportion on the mechanical properties of laminated veneer lumber (LVL) made from secondary quality hardwood

Citra Yanto Ciki Purba, Guillaume Pot, Joffrey Viguier, Julien Ruelle and Louis Denaud
European Journal of Wood and Wood Products 77 (3) 393 (2019)
DOI: 10.1007/s00107-019-01400-3
See this article

Use of computed tomography to determine penetration paths and the distribution of melamine resin in thermally-modified beech veneers after plasma treatment

Richard Wascher, Florian Bittner, Georg Avramidis, et al.
Composites Part A: Applied Science and Manufacturing 132 105821 (2020)
DOI: 10.1016/j.compositesa.2020.105821
See this article

Acceptability testing and development of a novel wood lathe balanced rest

Ernyl S. Onrejas, Jonathan O. Etcuban, Redjie D. Arcadio, et al.
Archives of Mechanical Technology and Materials 39 (1) 59 (2019)
DOI: 10.2478/amtm-2019-0011
See this article

Veneer and plywood properties of yemane (Gmelina arborea Roxb.) from 3-, 5-, and 7-year-old plantation trees

Juanito P. Jimenez, Dennis M. Gilbero and Marina A. Alipon
International Wood Products Journal 12 (4) 277 (2021)
DOI: 10.1080/20426445.2021.1979823
See this article